I installed WireGuard on my host and set this configuration /etc/wireguard/wg0.conf:

[Interface]
Address = 10.0.0.1/24
ListenPort = 51820
PrivateKey = [REDACTED]
PostUp = iptables -A FORWARD -i %i -j ACCEPT; iptables -t nat -A POSTROUTING -o ens3 -j MASQUERADE
PostDown = iptables -D FORWARD -i %i -j ACCEPT; iptables -t nat -D POSTROUTING -o ens3 -j MASQUERADE


[Peer]
PublicKey = [REDACTED]
PresharedKey = [REDACTED]
AllowedIPs = 10.0.0.2/32

[Peer]
PublicKey = [REDACTED]
PresharedKey = [REDACTED]
AllowedIPs = 10.0.0.3/32

[Peer]
PublicKey = [REDACTED]
PresharedKey = [REDACTED]
AllowedIPs = 10.0.0.4/32

[Peer]
PublicKey = [REDACTED]
PresharedKey = [REDACTED]
AllowedIPs = 10.0.0.5/32

[Peer]
PublicKey = [REDACTED]
PresharedKey = [REDACTED]
AllowedIPs = 10.0.0.6/32

[Peer]
PublicKey = [REDACTED]
PresharedKey = [REDACTED]
AllowedIPs = 10.0.0.7/32

[Peer]
PublicKey = [REDACTED]
PresharedKey = [REDACTED]
AllowedIPs = 10.0.0.8/32

[Peer]
PublicKey = [REDACTED]
PresharedKey = [REDACTED]
AllowedIPs = 10.0.0.9/32

[Peer]
PublicKey = [REDACTED]
PresharedKey = [REDACTED]
AllowedIPs = 10.0.0.10/32

[Peer]
PublicKey = [REDACTED]
PresharedKey = [REDACTED]
AllowedIPs = 10.0.0.11/32

Nmap scan when wg0 is down:

Starting Nmap 7.93 ( https://nmap.org ) at 2024-08-16 03:26 CDT
Host is up (0.050s latency).
Not shown: 998 closed tcp ports (conn-refused)
PORT    STATE    SERVICE
22/tcp  open     ssh
179/tcp filtered bgp

Nmap done: 1 IP address (1 host up) scanned in 1.93 seconds

Nmap scan when wg0 is up:

Starting Nmap 7.93 ( https://nmap.org ) at 2024-08-16 03:27 CDT
All 1000 scanned ports are in ignored states.
Not shown: 1000 filtered tcp ports (no-response)

Nmap done: 1 IP address (1 host up) scanned in 201.43 seconds

I also cannot connect to host via ssh. How to fix this issue?

Upd. Fixed my changing server WireGuard IP to 10.0.1.1. 10.0.0.1 was already taken

      • atzanteol@sh.itjust.worksEnglish
        1·
        27 days ago

        Ah - I see.

        I can never remember how all the iptables stuff works but here is what I have in my configuration which is basically attempting the same thing:

        PostUp   = iptables -A FORWARD -i wg0 -j ACCEPT; iptables -A FORWARD -o wg0 -j ACCEPT; iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE; iptables -t nat -A POSTROUTING -o wg0 -j MASQUERADE
PostDown = iptables -D FORWARD -i wg0 -j ACCEPT; iptables -D FORWARD -o wg0 -j ACCEPT; iptables -t nat -D POSTROUTING -o eth0 -j MASQUERADE; iptables -t nat -D POSTROUTING -o wg0 -j MASQUERADE

        Mine’s a little different and works for me.

  • Muehe@lemmy.ml
    2·
    27 days ago

    I think the problem might be your PostUp/PostDown lines have an in-interface (-i) but are missing an out-interface (-o) for the forwarding. Try this:

    PostUp   = iptables -A FORWARD -i %i -j ACCEPT; iptables -A FORWARD -o %i -j ACCEPT; iptables -t nat -A POSTROUTING -o ens3 -j MASQUERADE
PostDown = iptables -D FORWARD -i %i -j ACCEPT; iptables -D FORWARD -o %i -j ACCEPT; iptables -t nat -D POSTROUTING -o ens3 -j MASQUERADE
  • just_another_person@lemmy.world
    42·
    27 days ago

    Because the default route is changing. You have ALL traffic being routed over Wireguard here. How would you expect that to allow the interface routing to work for the local network if you’re telling this to punt all traffic to this specific connection?

    • Muehe@lemmy.ml
      2·
      27 days ago

      You have ALL traffic being routed over Wireguard here.

      Please correct me if I’m wrong, but isn’t it the other way around? All Wireguard traffic is forwarded to the local interface.

        • Muehe@lemmy.ml
          1·
          27 days ago

          I don’t think that’s what the setting does. Anyway, I have them set to a /32 IP in my server config and it works nonetheless. I get full access to the /24 behind the server from the client.

            • Muehe@lemmy.ml
              1·
              27 days ago

              What are you trying to say? That reply also shows AllowedIPs set to a /32 on the server side.

              • just_another_person@lemmy.world
                11·
                27 days ago

                For Peers. There’s no other route in OPs post. Like they said, when wg0 goes up, he can’t reach anything else. All that happens is this interface comes out, changes the routing tables and forwarding, but doesn’t go anywhere. It needs to be routed to the existing default gateway of the host. All this does is blackhole to the wg0 interface.

                • Muehe@lemmy.ml
                  1·
                  27 days ago

                  Like I said in another thread on this post, I’m pretty sure that’s because they are forwarding input but not output in the PostUp rules. Setting a /32 in AllowedIPs works fine for me.

                • atzanteol@sh.itjust.worksEnglish
                  1·
                  27 days ago

                  What “other route” are you expecting to see? My configuration looks very similar to OPs though I have an extra iptables entry in PostUp:

                  PostUp   = iptables -A FORWARD -i wg0 -j ACCEPT; iptables -A FORWARD -o wg0 -j ACCEPT; iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE; iptables -t nat -A POSTROUTING -o wg0 -j MASQUERADE

                  Is that what you mean?

      • just_another_person@lemmy.world
        12·
        27 days ago

        Well, I mean…I can’t give you an entire tutorial on how Wireguard works here, but you have it way wrong.

        If you’re not sure of the concepts and what you’re trying to do, I don’t know how to answer any questions for you. If you’re not familiar with what split-tunneling, subnet routing, and routing tables…you need to get way familiar before you start messing with this.

        Your rules aren’t the problem. You’re only allowing a single IP at a time across many connections here. Learn to read your routing tables and debug from there.